Samsung Galaxy Note Pro 12.2 P905XXUABOK3
SM-P905 1 country Android 5.0.2 (Lollipop)

Samsung Galaxy Note Pro 12.2 P905XXUABOK3 Firmware

Samsung Galaxy Note Pro 12.2 P905XXUABOK3 is an Android 5.0.2 (Lollipop) firmware for Australia (XSA). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P905XXUABOJ1: Android updated from Android 5.0.2 (KitKat) to Android 5.0.2 (Lollipop). A newer build for SM-P905 is available: P905XXUBML3.

Download firmware
8.9/10 (480)8,605 times
Android 5.0.2 (Lollipop)
OS Version
2015-11-18
First release
other regions until 2015-12-02
1
Countries
1
CSC codes
A (10)
Bootloader binary

Bootloader binary A (10). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Note Pro 12.2 use bootloader binary U (30) (latest: P905XXUBML3). If your device already runs binary U (30), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    ModelRegionCSC VersionMODEM/CP VersionBuild DateRelease dateSizeFile nameDownload
    SM-P905
    XSA Australia
    		P905XSAABOK2P905XXUABOF4 2015-12-02 2015-12-02 1.359 GiB
    SM-P905_1_20151202094201_d53k0bnkbq_fac.zip
    		Download
    SM-P905
    XSA Australia
    		P905ABOK2P905XXUABOK3 2015-11-18 — — — Download

    No matching downloads

    How to flash P905XXUABOK3

    • P905XXUABOK3 has bootloader binary A (10). Your device must run binary A (10) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid
    • Display diagonal31 cm (12.2")
    • Display resolution2560 x 1600 pixels
    • Display technologyLCD
    • Processor frequency2.3 GHz
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • Front camera resolution2 MP
    • Wi-Fi standardWi-Fi 5 (802.11ac)
    • Weight753 g

    Frequently Asked Questions

    P905XXUABOK3 is Android 5.0.2 (Lollipop) firmware for Samsung Galaxy Note Pro 12.2, released for Australia (XSA). Samsung built it on 2015-11-18.

    No. A newer build for SM-P905 is available: P905XXUBML3. Install it instead of P905XXUABOK3 unless you need this exact version. The previous build was P905XXUABOJ1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.359 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Note Pro 12.2 must be on bootloader binary A (10) or lower.

    This build uses bootloader binary A (10). It can be flashed on a Samsung Galaxy Note Pro 12.2 running binary A (10) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 23 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note Pro 12.2

    No changelog details available.
    Model firmware by region