Samsung Galaxy y S5360DXMJ1 Firmware
Samsung Galaxy y S5360DXMJ1 is an Android 2.3.6 (Gingerbread) firmware for 5 countries, 11 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build S5360DXMI1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-S5360 is available: S5360ZHLG1.
9.3/10 (479)36,190 times
Android 2.3.6 (Gingerbread)
OS Version
2013-11-06
First release
other regions until 2013-11-12
n/a
Security patch
5
Countries
11
CSC codes
D (13)
Bootloader binary
Bootloader binary D (13). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.
Newer builds of Samsung Galaxy y use bootloader binary Z (35) (latest: S5360ZHLG1). If your device already runs binary Z (35), this build cannot be flashed.
All regional downloads
Pick your region (CSC) to download the matching firmware package.
Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
11
MODEM/CP Version: S5360DXMI1
No matching downloads
Device specifications
- Launched withAndroid 2.3
- Display diagonal7.62 cm (3")
- Display resolution320 x 240 pixels
- Display typeTFT
- Processor frequency0.832 GHz
- Rear camera resolution2 MP
- Rear camera typeSingle camera
- SIM cardsSingle SIM
- Battery capacity120 mAh
- Weight97.5 g
How to flash S5360DXMJ1
- Install Samsung USB Drivers:Download Official Drivers
- Download Odin Flash Tool:
- S5360DXMJ1 has bootloader binary D (13). Your device must run binary D (13) or lower: it is the 5th character from the end of your current build number.
- CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
- HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
- The Download Mode key combo depends on the model: see all combos.
Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.
Frequently Asked Questions
S5360DXMJ1 is Android 2.3.6 (Gingerbread) firmware for Samsung Galaxy y, released for 5 countries, 11 CSC codes. Samsung built it on 2013-11-06.
No. A newer build for GT-S5360 is available: S5360ZHLG1. Install it instead of S5360DXMJ1 unless you need this exact version. The previous build was S5360DXMI1.
Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 125.831 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy y must be on bootloader binary D (13) or lower.
This build uses bootloader binary D (13). It can be flashed on a Samsung Galaxy y running binary D (13) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 2 other builds of this model use the same binary, so you can switch between them in both directions.