GT-S7710 1 country Android 4.1.2

Samsung Galaxy Xcover2 S7710XWAOB1 Firmware

Name: Samsung Galaxy Xcover2 (GT-S7710)
Brand: Samsung
Availability: InStock

Samsung Galaxy Xcover2 S7710XWAOB1 is an Android 4.1.2 firmware for Netherlands (XEN). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build S7710XWANI5 https://samfirm.shop/build/S7710XWANI5: Android updated from Android 4.1.2 (Jelly Bean) to Android 4.1.2. A newer build for GT-S7710 is available: S7710XXAOB2 https://samfirm.shop/build/S7710XXAOB2.

8.7/10 (471)8,516 times

Android 4.1.2

OS Version

2015-02-06

First release

other regions until 2015-02-24

n/a

Security patch

Countries

CSC codes

W (32)

Bootloader binary

Bootloader binary W (32). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Xcover2 use bootloader binary X (33) (latest: S7710XXAOB2). If your device already runs binary X (33), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: S7710XWAOB1

Model	Region	CSC Version	Build Date	Release date	Size	File name	Download
GT-S7710	XEN Netherlands	S7710XENAOA2	2015-02-24	2015-02-24	676.083 MiB	GT-S7710_XEN_1_20150224194730_iu9oji14jw_fac.zip
GT-S7710	XEN Netherlands	S7710AOA2	2015-02-06	—	—	—

Device specifications

Launched withAndroid 4.1
Display diagonal10.2 cm (4")
Display resolution480 x 800 pixels
Display typeTFT
Processor frequency1 GHz
Rear camera resolution5 MP
Rear camera typeSingle camera
SIM cardsSingle SIM
Battery capacity1700 mAh
Weight148 g

How to flash S7710XWAOB1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

S7710XWAOB1 has bootloader binary W (32). Your device must run binary W (32) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

S7710XWAOB1 is Android 4.1.2 firmware for Samsung Galaxy Xcover2, released for Netherlands (XEN). Samsung built it on 2015-02-06.

No. A newer build for GT-S7710 is available: S7710XXAOB2. Install it instead of S7710XWAOB1 unless you need this exact version. The previous build was S7710XWANI5.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 676.083 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Xcover2 must be on bootloader binary W (32) or lower.

This build uses bootloader binary W (32). It can be flashed on a Samsung Galaxy Xcover2 running binary W (32) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.