SM-T311 5 countries Android 4.4.2 (KitKat)

Samsung Galaxy Tab3 8.0 T311XXUBNI3 Firmware

Name: Samsung Galaxy Tab3 8.0 (SM-T311)
Brand: Samsung
Availability: InStock

Samsung Galaxy Tab3 8.0 T311XXUBNI3 is an Android 4.4.2 (KitKat) firmware for 5 countries, 6 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T311XXUBNI2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-T311 is available: T311UBUBOI1.

8.9/10 (450)25,852 times

Android 4.4.2 (KitKat)

OS Version

n/a

Build Date

n/a

Security patch

Countries

CSC codes

U (30)

Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: T311XXUBNI1

Model	Region	CSC Version	Size	File name
SM-T311	AFG Afghanistan	T311OJVBNI1	—	—
SM-T311	LYS Libya	T311OJVBNI1	—	—
SM-T311	SAC Algeria	T311OJVBNI1	—	—
SM-T311	THR Iran	T311OJVBNI1	—	—
SM-T311	TMC Algeria	T311OJVBNI1	—	—
SM-T311	WTL Saudi Arabia	T311OJVBNI1	—	—

Device specifications

Launched withAndroid
Display diagonal20.3 cm (8")
Display resolution1280 x 800 pixels
Processor frequency1.5 GHz
Processor familySamsung Exynos
Processor model4412
Rear camera resolution5 MP
Rear camera typeSingle camera
Front camera resolution1.3 MP
Wi-Fi standardWi-Fi 4 (802.11n)
Weight314 g

How to flash T311XXUBNI3

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

T311XXUBNI3 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

T311XXUBNI3 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Tab3 8.0, released for 5 countries, 6 CSC codes.

No. A newer build for SM-T311 is available: T311UBUBOI1. Install it instead of T311XXUBNI3 unless you need this exact version. The previous build was T311XXUBNI2.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Tab3 8.0 must be on bootloader binary U (30) or lower.

This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy Tab3 8.0 running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 21 other builds of this model use the same binary, so you can switch between them in both directions.