Samsung Galaxy Tab3 8.0 T311XWUANC1
SM-T311 3 countries Android 4.2.2 (Jelly Bean)

Samsung Galaxy Tab3 8.0 T311XWUANC1 Firmware

Samsung Galaxy Tab3 8.0 T311XWUANC1 is an Android 4.2.2 (Jelly Bean) firmware for Indonesia (XSE), Singapore (XSP), Thailand (THL). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T311XXUANA2: Android updated from Jelly(Android Bean) to Android 4.2.2 (Jelly Bean). A newer build for SM-T311 is available: T311UBUBOI1.

Download firmware
8.9/10 (480)12,698 times
Android 4.2.2 (Jelly Bean)
OS Version
2014-03-07
Build Date
3
Countries
3
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: T311DXUAMK1
    ModelRegionCSC VersionSizeFile nameDownload
    SM-T311
    THL Thailand
    XSE Indonesia
    		T311OLBANC1 1.301 GiB
    SM-T311_1_20151105192413_ctn99igtf6_fac.zip
    		Download
    SM-T311
    XSP Singapore
    		T311OLBANC1 1.301 GiB
    SM-T311_XSP_1_20141001143850_ytmwd5dqcs_fac.zip
    		Download

    No matching downloads

    How to flash T311XWUANC1

    • T311XWUANC1 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid
    • Display diagonal20.3 cm (8")
    • Display resolution1280 x 800 pixels
    • Processor frequency1.5 GHz
    • Processor familySamsung Exynos
    • Processor model4412
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Front camera resolution1.3 MP
    • Wi-Fi standardWi-Fi 4 (802.11n)
    • Weight314 g

    Frequently Asked Questions

    T311XWUANC1 is Android 4.2.2 (Jelly Bean) firmware for Samsung Galaxy Tab3 8.0, released for Indonesia (XSE), Singapore (XSP), Thailand (THL). Samsung built it on 2014-03-07.

    No. A newer build for SM-T311 is available: T311UBUBOI1. Install it instead of T311XWUANC1 unless you need this exact version. The previous build was T311XXUANA2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Tab3 8.0 must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy Tab3 8.0 running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 21 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Tab3 8.0

    No changelog details available.
    Model firmware by region