Samsung Galaxy Tab3 8.0 T311XXUBNK2
SM-T311 7 countries Android 4.4.2 (KitKat)

Samsung Galaxy Tab3 8.0 T311XXUBNK2 Firmware

Samsung Galaxy Tab3 8.0 T311XXUBNK2 is an Android 4.4.2 (KitKat) firmware for 7 countries, 7 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T311UBUBNK1: Android updated from Android 4.4.2 (Jelly) to Android 4.4.2 (KitKat). A newer build for SM-T311 is available: T311UBUBOI1.

Download firmware
9.2/10 (481)30,242 times
Android 4.4.2 (KitKat)
OS Version
2014-11-06
Build Date
7
Countries
7
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: T311XXUBNI1
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-T311
    ATL Spain
    		T311VFGBNK1 2014-12-09 1.274 GiB
    SM-T311_1_20170411181213_pobk4h77tm_fac.zip
    		Download
    SM-T311
    CAC Uzbekistan
    SEK Ukraine
    SER Russia
    SKZ Kazakhstan
    +1 more country
    MGF
    		T311OXEBNK2 — 1.386 GiB
    SM-T311_1_20170323145000_0j49jm5vty_fac.zip
    		Download
    SM-T311
    VDH Hungary
    		T311VFGBNK1 — 1.326 GiB
    SM-T311_1_20170410134926_xpsrggnvy0_fac.zip
    		Download

    No matching downloads

    How to flash T311XXUBNK2

    • T311XXUBNK2 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of T311XXUBNK2 by region

    Samsung released this build in all regions (1) on the same day, December 9, 2014.

    Device specifications

    • Launched withAndroid
    • Display diagonal20.3 cm (8")
    • Display resolution1280 x 800 pixels
    • Processor frequency1.5 GHz
    • Processor familySamsung Exynos
    • Processor model4412
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Front camera resolution1.3 MP
    • Wi-Fi standardWi-Fi 4 (802.11n)
    • Weight314 g

    Frequently Asked Questions

    T311XXUBNK2 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Tab3 8.0, released for 7 countries, 7 CSC codes. Samsung built it on 2014-11-06.

    No. A newer build for SM-T311 is available: T311UBUBOI1. Install it instead of T311XXUBNK2 unless you need this exact version. The previous build was T311UBUBNK1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Tab3 8.0 must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy Tab3 8.0 running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 21 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Tab3 8.0

    No changelog details available.
    Model firmware by region