Samsung Galaxy Tab 4 8.0 T330ZCU1ANG2
SM-T330 1 country Android 4.4.2 (KitKat)

Samsung Galaxy Tab 4 8.0 T330ZCU1ANG2 Firmware

Samsung Galaxy Tab 4 8.0 T330ZCU1ANG2 is an Android 4.4.2 (KitKat) firmware for China (CHN). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T330XXU1ANF2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-T330 is available: T330XXS1BSB1.

Download firmware
8.7/10 (480)4,413 times
Android 4.4.2 (KitKat)
OS Version
2014-07-23
Build Date
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: T330ZCU1ANG2
    ModelRegionCSC VersionSizeFile nameDownload
    SM-T330
    CHN China
    		T330CHN1ANG2 1.054 GiB
    SM-T330_1_20170227111426_6if1u52bos_fac.zip
    		Download

    No matching downloads

    How to flash T330ZCU1ANG2

    • T330ZCU1ANG2 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid
    • Display diagonal20.3 cm (8")
    • Display resolution1280 x 800 pixels
    • Processor frequency1.2 GHz
    • Rear camera resolution3 MP
    • Rear camera typeSingle camera
    • Front camera resolution1.3 MP
    • Wi-Fi standardWi-Fi 4 (802.11n)
    • Weight320 g

    Frequently Asked Questions

    T330ZCU1ANG2 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Tab 4 8.0, released for China (CHN). Samsung built it on 2014-07-23.

    No. A newer build for SM-T330 is available: T330XXS1BSB1. Install it instead of T330ZCU1ANG2 unless you need this exact version. The previous build was T330XXU1ANF2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.054 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Tab 4 8.0 must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Tab 4 8.0 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 35 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Tab 4 8.0

    · The security of your device has been improved.

    No changelog details available.
    Model firmware by region