Samsung Galaxy Star2 Plus G350EXXU0AOF3
SM-G350E 4 countries Android 4.4.2 (KitKat)

Samsung Galaxy Star2 Plus G350EXXU0AOF3 Firmware

Samsung Galaxy Star2 Plus G350EXXU0AOF3 is an Android 4.4.2 (KitKat) firmware for 4 countries, 4 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G350EXWU0AOE2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G350E is available: G350EXXS0AQD1.

Download firmware
9.1/10 (456)17,186 times
Android 4.4.2 (KitKat)
OS Version
2015-06-22
Build Date
4
Countries
4
CSC codes
0
Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: G350EXXU0AOF3
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-G350E
    AFG Afghanistan
    PAK Pakistan
    		G350EOJV0AOF1 — 555.568 MiB
    SM-G350E_1_20170610132114_6ufmte92xy_fac.zip
    SM-G350E
    SEK Ukraine
    SER Russia
    		G350EOXE0AOF3 2015-07-04 539.421 MiB
    SM-G350E_1_20170403074826_qutbjyf21g_fac.zip

    No matching downloads

    How to flash G350EXXU0AOF3

    • G350EXXU0AOF3 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of G350EXXU0AOF3 by region

    Samsung released this build in all regions (1) on the same day, July 4, 2015.

    Device specifications

    • Launched withAndroid 4.4
    • Display diagonal10.9 cm (4.3")
    • Display resolution480 x 800 pixels
    • Display typeTFT
    • Processor frequency1.2 GHz
    • Processor modelA7
    • RAM0.5 GB
    • Rear camera resolution3 MP
    • Rear camera typeSingle camera
    • SIM cardsDual SIM
    • Battery capacity1800 mAh
    • Weight129 g

    Frequently Asked Questions

    G350EXXU0AOF3 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Star2 Plus, released for 4 countries, 4 CSC codes. Samsung built it on 2015-06-22.

    No. A newer build for SM-G350E is available: G350EXXS0AQD1. Install it instead of G350EXXU0AOF3 unless you need this exact version. The previous build was G350EXWU0AOE2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Star2 Plus must be on bootloader binary 0 or lower.

    This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy Star2 Plus running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 16 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Star2 Plus

    No changelog details available.
    Model firmware by region