SM-G928G 2 countries Android 7.0 (Nougat)

Samsung Galaxy S6 Edge+ G928GUBS5CTK1 Firmware

Name: Samsung Galaxy S6 Edge+ (SM-G928G)
Brand: Samsung
Availability: InStock

First release: Dec 2, 2020

Samsung Galaxy S6 Edge+ G928GUBS5CTK1 is an Android 7.0 (Nougat) firmware for Panama (CPA), Puerto Rico (PCT). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G928GUBS5CTJC https://samfirm.shop/build/G928GUBS5CTJC, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G928G is available: G928GUBU5CVGH https://samfirm.shop/build/G928GUBU5CVGH.

Download firmware 9.0 (470)9,068 times

Android 7.0 (Nougat)

OS Version

2020-12-02

Build Date

2018-08-01

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 5. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: G928GUBS5CRH2

Model	Region	CSC Version	Release date	Size	File name	Download
SM-G928G	CPA Panama PCT Puerto Rico	G928GUWA5CTK1	2020-12-02	2.416 GiB	SM-G928G_1_20201202095933_pcw55bna7c_fac.zip	Download

How to flash G928GUBS5CTK1

G928GUBS5CTK1 has bootloader binary 5. Your device must run binary 5 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

What's new in G928GUBS5CTK1

· Security patch update

Rollout of G928GUBS5CTK1 by region

Samsung released this build in all regions (2) on the same day, December 2, 2020.

Device specifications

Launched withAndroid 5.1
Display diagonal14.5 cm (5.7")
Display resolution2560 x 1440 pixels
Display typeSAMOLED
RAM4 GB
Rear camera resolution16 MP
Rear camera typeSingle camera
Battery capacity3000 mAh
Weight153 g

Specifications of SM-G928, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

Frequently Asked Questions

G928GUBS5CTK1 is Android 7.0 (Nougat) firmware for Samsung Galaxy S6 Edge+, released for Panama (CPA), Puerto Rico (PCT). It includes the 2018-08-01 security patch. Samsung built it on 2020-12-02.

No. A newer build for SM-G928G is available: G928GUBU5CVGH. Install it instead of G928GUBS5CTK1 unless you need this exact version. The previous build was G928GUBS5CTJC.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.416 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy S6 Edge+ must be on bootloader binary 5 or lower.

This build uses bootloader binary 5. It can be flashed on a Samsung Galaxy S6 Edge+ running binary 5 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 47 other builds of this model use the same binary, so you can switch between them in both directions.