Samsung J1 Mini Prime J106FJVS0ARB1
SM-J106F 2 countries Android 6.0.1 (Marshmallow)

Samsung J1 Mini Prime J106FJVS0ARB1 Firmware

Samsung J1 Mini Prime J106FJVS0ARB1 is an Android 6.0.1 (Marshmallow) firmware for Russia (SER), Uzbekistan (CAC). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J106FJVS0ARA1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J106F is available: J106FJVU0ARL1.

Download firmware
9.3/10 (478)8,813 times
Android 6.0.1 (Marshmallow)
OS Version
2018-02-08
Build Date
2
Countries
2
CSC codes
0
Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: J106FJVU0AQI2
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-J106F
    CAC Uzbekistan
    SER Russia
    		J106FOXE0AQI2 2018-03-05 1.335 GiB
    SM-J106F_2_20180509131301_xbr2f2mihs_fac.zip
    		Download

    No matching downloads

    How to flash J106FJVS0ARB1

    • J106FJVS0ARB1 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of J106FJVS0ARB1 by region

    Samsung released this build in all regions (2) on the same day, March 5, 2018.

    Device specifications

    • Display diagonal10.2 cm (4")
    • Display resolution480 x 800 pixels
    • Display typeTFT
    • Processor frequency1.5 GHz
    • RAM1 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Battery capacity1500 mAh
    • Weight126 g

    Frequently Asked Questions

    J106FJVS0ARB1 is Android 6.0.1 (Marshmallow) firmware for Samsung J1 Mini Prime, released for Russia (SER), Uzbekistan (CAC). Samsung built it on 2018-02-08.

    No. A newer build for SM-J106F is available: J106FJVU0ARL1. Install it instead of J106FJVS0ARB1 unless you need this exact version. The previous build was J106FJVS0ARA1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.335 GiB; keep about twice that free on the computer to unzip it. The Samsung J1 Mini Prime must be on bootloader binary 0 or lower.

    This build uses bootloader binary 0. It can be flashed on a Samsung J1 Mini Prime running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 18 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung J1 Mini Prime

    No changelog details available.
    Model firmware by region