GT-P7300 2 countries Android 3.2 (Honeycomb)

Samsung Galaxy Tab 8.9 (3G + WiFi) P7300XWKL4 Firmware

Name: Samsung Galaxy Tab 8.9 (3G + WiFi) (GT-P7300)
Brand: Samsung
Availability: InStock

Samsung Galaxy Tab 8.9 (3G + WiFi) P7300XWKL4 is an Android 3.2 (Honeycomb) firmware for Montenegro (TOP), Nigeria (ECT). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P7300UBLP5 https://samfirm.shop/build/P7300UBLP5: Android updated from Ice(Android Cream) to Android 3.2 (Honeycomb); bootloader binary raised from U (30) to X (33), so after installing it there is no way back to older builds. A newer build for GT-P7300 is available: P7300ZSLPD https://samfirm.shop/build/P7300ZSLPD.

8.9/10 (472)8,705 times

Android 3.2 (Honeycomb)

OS Version

2011-12-23

Build Date

n/a

Security patch

Countries

CSC codes

X (33)

Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Tab 8.9 (3G + WiFi) use bootloader binary Z (35) (latest: P7300ZSLPD). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: P7300XXKJ6

Model	Region	CSC Version	Release date	Size	File name	Download
GT-P7300	ECT Nigeria	P7300OJVKL2	2012-03-17	—	—
GT-P7300	TOP Montenegro	P7300OXXKL3	2012-01-13	—	—

Device specifications

Display diagonal22.6 cm (8.9")
Display resolution1280 x 800 pixels
Processor frequency1 GHz
Processor familyNVIDIA Tegra
Wi-Fi standardWi-Fi 4 (802.11n)
Weight465 g

How to flash P7300XWKL4

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

P7300XWKL4 has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

P7300XWKL4 is Android 3.2 (Honeycomb) firmware for Samsung Galaxy Tab 8.9 (3G + WiFi), released for Montenegro (TOP), Nigeria (ECT). Samsung built it on 2011-12-23.

No. A newer build for GT-P7300 is available: P7300ZSLPD. Install it instead of P7300XWKL4 unless you need this exact version. The previous build was P7300UBLP5.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Tab 8.9 (3G + WiFi) must be on bootloader binary X (33) or lower.

This build uses bootloader binary X (33). It can be flashed on a Samsung Galaxy Tab 8.9 (3G + WiFi) running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 10 other builds of this model use the same binary, so you can switch between them in both directions.