Samsung Galaxy Tab 8.9 (3G + WiFi) P7300XXLQC
GT-P7300 6 countries Android 3.2 (Honeycomb)

Samsung Galaxy Tab 8.9 (3G + WiFi) P7300XXLQC Firmware

Samsung Galaxy Tab 8.9 (3G + WiFi) P7300XXLQC is an Android 3.2 (Honeycomb) firmware for 6 countries, 6 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P7300XXLQ6: Android updated from Ice(Android Cream) to Android 3.2 (Honeycomb). A newer build for GT-P7300 is available: P7300ZSLPD.

Download firmware
9.1/10 (457)26,385 times
Android 3.2 (Honeycomb)
OS Version
6
Countries
6
CSC codes
X (33)
Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Tab 8.9 (3G + WiFi) use bootloader binary Z (35) (latest: P7300ZSLPD). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: P7300XXLQ6
    ModelRegionCSC VersionSizeFile nameDownload
    GT-P7300
    FOP Spain
    		P7300FOPLP4 — — Download
    GT-P7300
    NEE Nordic Europe
    		P7300OXXLP4 — — Download
    GT-P7300
    NSE
    		P7300OXXLP4 — — Download
    GT-P7300
    ROM Romania
    		P7300OXXLP4 — — Download
    GT-P7300
    SEB Baltic Europe
    		P7300OXXLP4 — — Download
    GT-P7300
    XEH Hungary
    		P7300OXXLP4 — — Download

    No matching downloads

    How to flash P7300XXLQC

    • P7300XXLQC has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal22.6 cm (8.9")
    • Display resolution1280 x 800 pixels
    • Processor frequency1 GHz
    • Processor familyNVIDIA Tegra
    • Wi-Fi standardWi-Fi 4 (802.11n)
    • Weight465 g

    Frequently Asked Questions

    P7300XXLQC is Android 3.2 (Honeycomb) firmware for Samsung Galaxy Tab 8.9 (3G + WiFi), released for 6 countries, 6 CSC codes.

    No. A newer build for GT-P7300 is available: P7300ZSLPD. Install it instead of P7300XXLQC unless you need this exact version. The previous build was P7300XXLQ6.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Tab 8.9 (3G + WiFi) must be on bootloader binary X (33) or lower.

    This build uses bootloader binary X (33). It can be flashed on a Samsung Galaxy Tab 8.9 (3G + WiFi) running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 10 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Tab 8.9 (3G + WiFi)

    No changelog details available.
    Model firmware by region