GT-P7300 4 countries

Samsung Galaxy Tab 8.9 (3G + WiFi) P7300ZSLPD Firmware

Name: Samsung Galaxy Tab 8.9 (3G + WiFi) (GT-P7300)
Brand: Samsung
Availability: InStock

Samsung Galaxy Tab 8.9 (3G + WiFi) P7300ZSLPD is an Android firmware for 4 countries, 4 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P7300ZSLPC, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. This is the newest build for GT-P7300.

8.8/10 (471)34,754 times

n/a

OS Version

2012-11-16

Build Date

n/a

Security patch

Countries

CSC codes

Z (35)

Bootloader binary

Bootloader binary Z (35). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

Model	Region	CSC Version	MODEM/CP Version	Build Date	Release date	Size	File name
GT-P7300	BRI Taiwan	P7300OZSLPD	P7300ZSLPD	2012-11-16	—	—	—
GT-P7300	BRI Taiwan	P7300OZSLPD	P7300XXLQ6	—	2012-12-12	—	—
GT-P7300	FET	P7300OZSLPD	P7300ZSLPD	2012-11-16	—	—	—
GT-P7300	FET	P7300OZSLPD	P7300XXLQ6	—	2012-12-12	—	—
GT-P7300	TGY Hong Kong SAR China	P7300OZSLPD	P7300ZSLPD	2012-11-16	—	—	—
GT-P7300	TGY Hong Kong SAR China	P7300OZSLPD	P7300XXLQ6	—	2012-12-12	—	—
GT-P7300	TWM	P7300OZSLPD	P7300ZSLPD	2012-11-16	—	—	—
GT-P7300	TWM	P7300OZSLPD	P7300XXLQ6	—	2012-12-12	—	—

Device specifications

Display diagonal22.6 cm (8.9")
Display resolution1280 x 800 pixels
Processor frequency1 GHz
Processor familyNVIDIA Tegra
Wi-Fi standardWi-Fi 4 (802.11n)
Weight465 g

How to flash P7300ZSLPD

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

P7300ZSLPD has bootloader binary Z (35). Your device must run binary Z (35) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

Yes. P7300ZSLPD is the newest build for GT-P7300 on SamFirm. The previous build was P7300ZSLPC.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Tab 8.9 (3G + WiFi) must be on bootloader binary Z (35) or lower.

This build uses bootloader binary Z (35). It can be flashed on a Samsung Galaxy Tab 8.9 (3G + WiFi) running binary Z (35) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 3 other builds of this model use the same binary, so you can switch between them in both directions.