GT-P7300 1 country Android 3.2 (Honeycomb)

Samsung Galaxy Tab 8.9 (3G + WiFi) P7300XXLQJ Firmware

Name: Samsung Galaxy Tab 8.9 (3G + WiFi) (GT-P7300)
Brand: Samsung
Availability: InStock

Samsung Galaxy Tab 8.9 (3G + WiFi) P7300XXLQJ is an Android 3.2 (Honeycomb) firmware for South Africa (XFV). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P7300XXLQI: Android updated from Ice(Android Cream) to Android 3.2 (Honeycomb). A newer build for GT-P7300 is available: P7300ZSLPD.

9.2/10 (470)4,245 times

Android 3.2 (Honeycomb)

OS Version

2013-11-26

Build Date

n/a

Security patch

Countries

CSC codes

X (33)

Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Tab 8.9 (3G + WiFi) use bootloader binary Z (35) (latest: P7300ZSLPD). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: P7300XXLQ6

Model	Region	CSC Version	Release date	Size	File name	Download
GT-P7300	XFV South Africa	P7300XFVLP4	2013-11-26	—	—

Device specifications

Display diagonal22.6 cm (8.9")
Display resolution1280 x 800 pixels
Processor frequency1 GHz
Processor familyNVIDIA Tegra
Wi-Fi standardWi-Fi 4 (802.11n)
Weight465 g

How to flash P7300XXLQJ

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

P7300XXLQJ has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

P7300XXLQJ is Android 3.2 (Honeycomb) firmware for Samsung Galaxy Tab 8.9 (3G + WiFi), released for South Africa (XFV). Samsung built it on 2013-11-26.

No. A newer build for GT-P7300 is available: P7300ZSLPD. Install it instead of P7300XXLQJ unless you need this exact version. The previous build was P7300XXLQI.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Tab 8.9 (3G + WiFi) must be on bootloader binary X (33) or lower.

This build uses bootloader binary X (33). It can be flashed on a Samsung Galaxy Tab 8.9 (3G + WiFi) running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 10 other builds of this model use the same binary, so you can switch between them in both directions.