Samsung Galaxy Ace S5830JPKS2
GT-S5830 2 countries Android 2.3.3 (Gingerbread)

Samsung Galaxy Ace S5830JPKS2 Firmware

Samsung Galaxy Ace S5830JPKS2 is an Android 2.3.3 (Gingerbread) firmware for United Arab Emirates (XSG), XSS. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build S5830JPKP9, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-S5830 is available: S5830ZSKPD.

9.4/10 (24)710 times
Android 2.3.3 (Gingerbread)
OS Version
2013-09-23
Build Date
n/a
Security patch
2
Countries
2
CSC codes
J (19)
Bootloader binary

Bootloader binary J (19). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Ace use bootloader binary Z (35) (latest: S5830ZSKPD). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: S5830XWKS2
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    GT-S5830
    XSG United Arab Emirates
    XSS
    		S5830OJPKS2 2012-02-23 147.038 MiB
    GT-S5830_XSG_1_20130923151432_5ukx6lcjxi_fac.zip

    No matching downloads

    How to flash S5830JPKS2

    • S5830JPKS2 has bootloader binary J (19). Your device must run binary J (19) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of S5830JPKS2 by region

    Samsung released this build in all regions (2) on the same day, February 23, 2012.

    Device specifications

    • Launched withAndroid 2.2
    • Display diagonal8.89 cm (3.5")
    • Display resolution320 x 480 pixels
    • Processor frequency0.8 GHz
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity1350 mAh
    • Weight113 g

    Frequently Asked Questions

    S5830JPKS2 is Android 2.3.3 (Gingerbread) firmware for Samsung Galaxy Ace, released for United Arab Emirates (XSG), XSS. Samsung built it on 2013-09-23.

    No. A newer build for GT-S5830 is available: S5830ZSKPD. Install it instead of S5830JPKS2 unless you need this exact version. The previous build was S5830JPKP9.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 147.038 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Ace must be on bootloader binary J (19) or lower.

    This build uses bootloader binary J (19). It can be flashed on a Samsung Galaxy Ace running binary J (19) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Ace

    No changelog details available.
    Model firmware by region