GT-S5830 1 country Android 2.3.3 (Gingerbread)

Samsung Galaxy Ace S5830XWKPJ Firmware

Name: Samsung Galaxy Ace (GT-S5830)
Brand: Samsung
Availability: InStock

Samsung Galaxy Ace S5830XWKPJ is an Android 2.3.3 (Gingerbread) firmware for South Africa (XFV). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build S5830WGLP2: Android updated from Android 2.3.6 (Gingerbread) to Android 2.3.3 (Gingerbread); bootloader binary raised from W (32) to X (33), so after installing it there is no way back to older builds. A newer build for GT-S5830 is available: S5830ZSKPD.

9.4/10 (471)4,302 times

Android 2.3.3 (Gingerbread)

OS Version

2011-06-22

Build Date

n/a

Security patch

Countries

CSC codes

X (33)

Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Ace use bootloader binary Z (35) (latest: S5830ZSKPD). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: S5830XFVKP1

Model	Region	CSC Version	Size	File name	Download
GT-S5830	XFV South Africa	S5830XWKP6	—	—

Device specifications

Launched withAndroid 2.2
Display diagonal8.89 cm (3.5")
Display resolution320 x 480 pixels
Processor frequency0.8 GHz
Rear camera resolution5 MP
Rear camera typeSingle camera
SIM cardsSingle SIM
Battery capacity1350 mAh
Weight113 g

How to flash S5830XWKPJ

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

S5830XWKPJ has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

S5830XWKPJ is Android 2.3.3 (Gingerbread) firmware for Samsung Galaxy Ace, released for South Africa (XFV). Samsung built it on 2011-06-22.

No. A newer build for GT-S5830 is available: S5830ZSKPD. Install it instead of S5830XWKPJ unless you need this exact version. The previous build was S5830WGLP2.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Ace must be on bootloader binary X (33) or lower.

This build uses bootloader binary X (33). It can be flashed on a Samsung Galaxy Ace running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 11 other builds of this model use the same binary, so you can switch between them in both directions.