GT-S6500D 2 countries Android 2.3.6 (Gingerbread)

Samsung GT-S6500D S6500DZSLI2 Firmware

Name: Samsung GT-S6500D (GT-S6500D)
Brand: Samsung
Availability: InStock

Samsung GT-S6500D S6500DZSLI2 is an Android 2.3.6 (Gingerbread) firmware for Hong Kong SAR China (TGY), Taiwan (BRI). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build S6500DZCLH1 https://samfirm.shop/build/S6500DZCLH1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. This is the newest build for GT-S6500D.

9.4/10 (480)6,549 times

Android 2.3.6 (Gingerbread)

OS Version

2012-09-28

Build Date

n/a

Security patch

Countries

CSC codes

Z (35)

Bootloader binary

Bootloader binary Z (35). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: S6500DZSLI2

Model	Region	CSC Version	Build Date	Release date	Size	File name	Download
GT-S6500D	BRI Taiwan	S6500DBRILI2	2012-09-28	2012-10-18	253.705 MiB	GT-S6500D_BRI_1_20120928154103_snceas4ejp.zip
GT-S6500D	TGY Hong Kong SAR China	S6500DTGYLI2	2012-09-28	2012-10-18	253.696 MiB	GT-S6500D_TGY_1_20120928155001_d6zmnwdmxi.zip

How to flash S6500DZSLI2

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

S6500DZSLI2 has bootloader binary Z (35). Your device must run binary Z (35) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

S6500DZSLI2 is Android 2.3.6 (Gingerbread) firmware for Samsung GT-S6500D, released for Hong Kong SAR China (TGY), Taiwan (BRI). Samsung built it on 2012-09-28.

Yes. S6500DZSLI2 is the newest build for GT-S6500D on SamFirm. The previous build was S6500DZCLH1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung GT-S6500D must be on bootloader binary Z (35) or lower.

This build uses bootloader binary Z (35). It can be flashed on a Samsung GT-S6500D running binary Z (35) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.