Samsung GT-S6500D S6500DXXLD3
GT-S6500D 2 countries Android 2.3.6 (Gingerbread)

Samsung GT-S6500D S6500DXXLD3 Firmware

Samsung GT-S6500D S6500DXXLD3 is an Android 2.3.6 (Gingerbread) firmware for BON, Hungary (TMH). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build S6500DXXLC4, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-S6500D is available: S6500DZSLI2.

Download firmware
9.3/10 (484)7,650 times
Android 2.3.6 (Gingerbread)
OS Version
2012-04-19
First release
other regions until 2012-04-23
2
Countries
2
CSC codes
X (33)
Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung GT-S6500D use bootloader binary Z (35) (latest: S6500DZSLI2). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: S6500DXXLD3
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    GT-S6500D
    BON
    		S6500DOXXLD2 2012-04-19 2012-05-09 — —
    GT-S6500D
    TMH Hungary
    		S6500DTMHLC1 2012-04-23 2012-05-04 250.856 MiB
    GT-S6500D_TMH_1_20120423133711_1tdknq3woh.zip

    No matching downloads

    How to flash S6500DXXLD3

    • S6500DXXLD3 has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of S6500DXXLD3 by region

    First release
    May 4, 2012
    Last region
    May 9, 2012
    Duration
    6 days
    Regions
    2
    1. Day 1 · · 1 region
      HungaryTMH
    2. Day 6 · · 1 region
      BON

    Frequently Asked Questions

    S6500DXXLD3 is Android 2.3.6 (Gingerbread) firmware for Samsung GT-S6500D, released for BON, Hungary (TMH). Samsung built it on 2012-04-19.

    No. A newer build for GT-S6500D is available: S6500DZSLI2. Install it instead of S6500DXXLD3 unless you need this exact version. The previous build was S6500DXXLC4.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 250.856 MiB; keep about twice that free on the computer to unzip it. The Samsung GT-S6500D must be on bootloader binary X (33) or lower.

    This build uses bootloader binary X (33). It can be flashed on a Samsung GT-S6500D running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 8 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung GT-S6500D

    No changelog details available.
    Model firmware by region