GT-S7500 3 countries Android 2.3.6 (Gingerbread)

Samsung GT-S7500 S7500JPLB1 Firmware

Name: Samsung GT-S7500 (GT-S7500)
Brand: Samsung
Availability: InStock

Samsung GT-S7500 S7500JPLB1 is an Android 2.3.6 (Gingerbread) firmware for Libya (BTC), Morocco (MED), United Arab Emirates (XSG). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build S7500DXMH1: bootloader binary raised from D (13) to J (19), so after installing it there is no way back to older builds. A newer build for GT-S7500 is available: S7500ZULH1.

9.0/10 (471)13,022 times

Android 2.3.6 (Gingerbread)

OS Version

2012-02-01

Build Date

n/a

Security patch

Countries

CSC codes

J (19)

Bootloader binary

Bootloader binary J (19). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung GT-S7500 use bootloader binary Z (35) (latest: S7500ZULH1). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: S7500XXLB1

Model	Region	CSC Version	Release date	Size	File name
GT-S7500	BTC Libya	S7500OJPLB1	—	—	—
GT-S7500	MED Morocco	S7500OJPLB1	2012-02-10	—	—
GT-S7500	XSG United Arab Emirates	S7500OJPLB1	2012-11-13	—	—

How to flash S7500JPLB1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

S7500JPLB1 has bootloader binary J (19). Your device must run binary J (19) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

S7500JPLB1 is Android 2.3.6 (Gingerbread) firmware for Samsung GT-S7500, released for Libya (BTC), Morocco (MED), United Arab Emirates (XSG). Samsung built it on 2012-02-01.

No. A newer build for GT-S7500 is available: S7500ZULH1. Install it instead of S7500JPLB1 unless you need this exact version. The previous build was S7500DXMH1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung GT-S7500 must be on bootloader binary J (19) or lower.

This build uses bootloader binary J (19). It can be flashed on a Samsung GT-S7500 running binary J (19) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.