Samsung GT-S7500 S7500XXLB1
GT-S7500 4 countries Android 2.3.6 (Gingerbread)

Samsung GT-S7500 S7500XXLB1 Firmware

Samsung GT-S7500 S7500XXLB1 is an Android 2.3.6 (Gingerbread) firmware for 4 countries, 4 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build S7500JPLG1: bootloader binary raised from J (19) to X (33), so after installing it there is no way back to older builds. A newer build for GT-S7500 is available: S7500ZULH1.

Download firmware
9.1/10 (477)17,643 times
Android 2.3.6 (Gingerbread)
OS Version
2012-02-01
Build Date
4
Countries
4
CSC codes
X (33)
Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung GT-S7500 use bootloader binary Z (35) (latest: S7500ZULH1). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: S7500XXLB1
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    GT-S7500
    AFR Kenya
    		S7500OJVLA2 2012-02-10 — — Download
    GT-S7500
    ECT Nigeria
    		S7500OJVLA2 2012-02-10 — — Download
    GT-S7500
    TUR Turkey
    		S7500OJVLA2 2012-02-10 — — Download
    GT-S7500
    XFE South Africa
    		S7500OJVLA2 2012-06-22 — — Download

    No matching downloads

    How to flash S7500XXLB1

    • S7500XXLB1 has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of S7500XXLB1 by region

    First release
    February 10, 2012
    Last region
    June 22, 2012
    Duration
    134 days
    Regions
    4
    1. Day 1 · · 3 regions
      KenyaAFRNigeriaECTTurkeyTUR
    2. Day 134 · · 1 region
      South AfricaXFE

    Frequently Asked Questions

    S7500XXLB1 is Android 2.3.6 (Gingerbread) firmware for Samsung GT-S7500, released for 4 countries, 4 CSC codes. Samsung built it on 2012-02-01.

    No. A newer build for GT-S7500 is available: S7500ZULH1. Install it instead of S7500XXLB1 unless you need this exact version. The previous build was S7500JPLG1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung GT-S7500 must be on bootloader binary X (33) or lower.

    This build uses bootloader binary X (33). It can be flashed on a Samsung GT-S7500 running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 9 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung GT-S7500

    No changelog details available.
    Model firmware by region