GT-S7500 1 country Android 2.3.6 (Gingerbread)

Samsung GT-S7500 S7500ZSLD3 Firmware

Name: Samsung GT-S7500 (GT-S7500)
Brand: Samsung
Availability: InStock

Samsung GT-S7500 S7500ZSLD3 is an Android 2.3.6 (Gingerbread) firmware for Taiwan (BRI). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build S7500XXNB1 https://samfirm.shop/build/S7500XXNB1: bootloader binary raised from X (33) to Z (35), so after installing it there is no way back to older builds. A newer build for GT-S7500 is available: S7500ZULH1 https://samfirm.shop/build/S7500ZULH1.

9.1/10 (477)3,155 times

Android 2.3.6 (Gingerbread)

OS Version

2012-08-10

Build Date

n/a

Security patch

Countries

CSC codes

Z (35)

Bootloader binary

Bootloader binary Z (35). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: S7500ZSLD3

Model	Region	CSC Version	Release date	Size	File name	Download
GT-S7500	BRI Taiwan	S7500BRILD3	2012-05-10	251.939 MiB	GT-S7500_BRI_1_20120810090653_22g1jlbfa7.zip

How to flash S7500ZSLD3

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

S7500ZSLD3 has bootloader binary Z (35). Your device must run binary Z (35) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

S7500ZSLD3 is Android 2.3.6 (Gingerbread) firmware for Samsung GT-S7500, released for Taiwan (BRI). Samsung built it on 2012-08-10.

No. A newer build for GT-S7500 is available: S7500ZULH1. Install it instead of S7500ZSLD3 unless you need this exact version. The previous build was S7500XXNB1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 251.939 MiB; keep about twice that free on the computer to unzip it. The Samsung GT-S7500 must be on bootloader binary Z (35) or lower.

This build uses bootloader binary Z (35). It can be flashed on a Samsung GT-S7500 running binary Z (35) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 3 other builds of this model use the same binary, so you can switch between them in both directions.