SM-T211 4 countries Android 4.4.2 (KitKat)

Samsung Galaxy Tab3 7.0 T211UBUBNL1 Firmware

Name: Samsung Galaxy Tab3 7.0 (SM-T211)
Brand: Samsung
Availability: InStock

Samsung Galaxy Tab3 7.0 T211UBUBNL1 is an Android 4.4.2 (KitKat) firmware for 4 countries, 4 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T211UBUBNK2 https://samfirm.shop/build/T211UBUBNK2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-T211 is available: T211XXBPA2 https://samfirm.shop/build/T211XXBPA2.

9.1/10 (454)17,382 times

Android 4.4.2 (KitKat)

OS Version

2015-02-17

Build Date

n/a

Security patch

Countries

CSC codes

U (30)

Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Tab3 7.0 use bootloader binary X (33) (latest: T211XXBPA2). If your device already runs binary X (33), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: T211UBUBNL1

Model	Region	CSC Version	Build Date	Release date	Size	File name
SM-T211	COO Colombia	T211UUBBNL1	—	—	—	—
SM-T211	CTP Paraguay	T211UWABNL1	2015-02-17	2015-02-17	958.586 MiB	SM-T211_1_20150914213526_3au7hbvdpy_fac.zip
SM-T211	EON Trinidad & Tobago	T211UUBBNL1	—	—	—	—
SM-T211	TPA Panama	T211UUBBNL1	—	—	—	—

Device specifications

Launched withAndroid
Display diagonal17.8 cm (7")
Display resolution1024 x 600 pixels
Processor frequency1.2 GHz
Rear camera resolution3 MP
Rear camera typeSingle camera
Front camera resolution1.3 MP
Wi-Fi standardWi-Fi 4 (802.11n)
Weight304 g

How to flash T211UBUBNL1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

T211UBUBNL1 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

T211UBUBNL1 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Tab3 7.0, released for 4 countries, 4 CSC codes. Samsung built it on 2015-02-17.

No. A newer build for SM-T211 is available: T211XXBPA2. Install it instead of T211UBUBNL1 unless you need this exact version. The previous build was T211UBUBNK2.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 958.586 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Tab3 7.0 must be on bootloader binary U (30) or lower.

This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy Tab3 7.0 running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 4 other builds of this model use the same binary, so you can switch between them in both directions.