Samsung Galaxy Tab3 7.0 T211XXBOD1
SM-T211 1 country Android 4.4.2 (KitKat)

Samsung Galaxy Tab3 7.0 T211XXBOD1 Firmware

Samsung Galaxy Tab3 7.0 T211XXBOD1 is an Android 4.4.2 (KitKat) firmware for Nordic Europe (NEE). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T211XXBOC1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-T211 is available: T211XXBPA2.

Download firmware
9.3/10 (479)8,784 times
Android 4.4.2 (KitKat)
OS Version
2015-04-08
First release
other regions until 2015-05-04
1
Countries
1
CSC codes
X (33)
Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    ModelRegionCSC VersionMODEM/CP VersionBuild DateRelease dateSizeFile nameDownload
    SM-T211
    NEE Nordic Europe
    		T211NEEBOD1T211XXBNJ3 2015-05-04 2015-05-04 831.027 MiB
    SM-T211_1_20150504114652_1w51685d9d_fac.zip
    		Download
    SM-T211
    NEE Nordic Europe
    		T211BOD1T211XXBOD1 2015-04-08 — — — Download

    No matching downloads

    How to flash T211XXBOD1

    • T211XXBOD1 has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid
    • Display diagonal17.8 cm (7")
    • Display resolution1024 x 600 pixels
    • Processor frequency1.2 GHz
    • Rear camera resolution3 MP
    • Rear camera typeSingle camera
    • Front camera resolution1.3 MP
    • Wi-Fi standardWi-Fi 4 (802.11n)
    • Weight304 g

    Frequently Asked Questions

    T211XXBOD1 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Tab3 7.0, released for Nordic Europe (NEE). Samsung built it on 2015-04-08.

    No. A newer build for SM-T211 is available: T211XXBPA2. Install it instead of T211XXBOD1 unless you need this exact version. The previous build was T211XXBOC1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 831.027 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Tab3 7.0 must be on bootloader binary X (33) or lower.

    This build uses bootloader binary X (33). It can be flashed on a Samsung Galaxy Tab3 7.0 running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 27 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Tab3 7.0

    No changelog details available.
    Model firmware by region