Samsung Galaxy Tab3 7.0 T211ZSANB1 Firmware
Samsung Galaxy Tab3 7.0 T211ZSANB1 is an Android 4.1.2 (Jelly Bean) firmware for Taiwan (BRI). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T211ZCANH1: Android updated from Jelly(Android Bean) to Android 4.1.2 (Jelly Bean); bootloader binary raised from C (12) to S (28), so after installing it there is no way back to older builds. A newer build for SM-T211 is available: T211XXBPA2.
8.7/10 (470)4,393 times
Android 4.1.2 (Jelly Bean)
OS Version
2014-02-17
Build Date
n/a
Security patch
1
Countries
1
CSC codes
S (28)
Bootloader binary
Bootloader binary S (28). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.
Newer builds of Samsung Galaxy Tab3 7.0 use bootloader binary X (33) (latest: T211XXBPA2). If your device already runs binary X (33), this build cannot be flashed.
All regional downloads
Pick your region (CSC) to download the matching firmware package.
Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
MODEM/CP Version: T211ZSANB1
Device specifications
- Launched withAndroid
- Display diagonal17.8 cm (7")
- Display resolution1024 x 600 pixels
- Processor frequency1.2 GHz
- Rear camera resolution3 MP
- Rear camera typeSingle camera
- Front camera resolution1.3 MP
- Wi-Fi standardWi-Fi 4 (802.11n)
- Weight304 g
How to flash T211ZSANB1
- Install Samsung USB Drivers:Download Official Drivers
- Download Odin Flash Tool:
- T211ZSANB1 has bootloader binary S (28). Your device must run binary S (28) or lower: it is the 5th character from the end of your current build number.
- CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
- HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
- The Download Mode key combo depends on the model: see all combos.
Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.
Frequently Asked Questions
T211ZSANB1 is Android 4.1.2 (Jelly Bean) firmware for Samsung Galaxy Tab3 7.0, released for Taiwan (BRI). Samsung built it on 2014-02-17.
No. A newer build for SM-T211 is available: T211XXBPA2. Install it instead of T211ZSANB1 unless you need this exact version. The previous build was T211ZCANH1.
Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 766.396 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Tab3 7.0 must be on bootloader binary S (28) or lower.
This build uses bootloader binary S (28). It can be flashed on a Samsung Galaxy Tab3 7.0 running binary S (28) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.