GT-I9070 2 countries Android 2.3.6 (Gingerbread)

Samsung Galaxy S Advance I9070UBLPL Firmware

Name: Samsung Galaxy S Advance (GT-I9070)
Brand: Samsung
Availability: InStock

Samsung Galaxy S Advance I9070UBLPL is an Android 2.3.6 (Gingerbread) firmware for Argentina (ARO), Uruguay (UPO). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9070UBLPK: Android updated from Jelly(Android Bean) to Android 2.3.6 (Gingerbread). A newer build for GT-I9070 is available: I9070ZSMG2.

9.2/10 (470)11,136 times

Android 2.3.6 (Gingerbread)

OS Version

2015-03-03

Build Date

n/a

Security patch

Countries

CSC codes

U (30)

Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S Advance use bootloader binary Z (35) (latest: I9070ZSMG2). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: I9070UBLPL

Model	Region	CSC Version	Build Date	Release date	Size	File name	Download
GT-I9070	ARO Argentina	I9070UVOLP9	—	—	—	—
GT-I9070	UPO Uruguay	I9070UVOLP9	2015-03-03	2015-03-03	—	—

How to flash I9070UBLPL

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

I9070UBLPL has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

I9070UBLPL is Android 2.3.6 (Gingerbread) firmware for Samsung Galaxy S Advance, released for Argentina (ARO), Uruguay (UPO). Samsung built it on 2015-03-03.

No. A newer build for GT-I9070 is available: I9070ZSMG2. Install it instead of I9070UBLPL unless you need this exact version. The previous build was I9070UBLPK.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S Advance must be on bootloader binary U (30) or lower.

This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy S Advance running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 5 other builds of this model use the same binary, so you can switch between them in both directions.