Samsung Galaxy S Advance I9070UBLPK
GT-I9070 1 country Android 2.3.6 (Gingerbread)

Samsung Galaxy S Advance I9070UBLPK Firmware

Samsung Galaxy S Advance I9070UBLPK is an Android 2.3.6 (Gingerbread) firmware for Argentina (ARO, PSN). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9070UBLPI: Android updated from Android 4.1.2 (Jelly Bean) to Android 2.3.6 (Gingerbread). A newer build for GT-I9070 is available: I9070ZSMG2.

Download firmware
9.3/10 (480)8,715 times
Android 2.3.6 (Gingerbread)
OS Version
2014-01-09
First release
other regions until 2014-02-26
1
Countries
2
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S Advance use bootloader binary Z (35) (latest: I9070ZSMG2). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: I9070UBLPK
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    GT-I9070
    ARO Argentina
    		I9070UVOLP8 2014-01-09 2014-04-02 — — Download
    GT-I9070
    PSN Argentina
    		I9070PSNLP7 2014-02-26 2014-02-26 — — Download

    No matching downloads

    How to flash I9070UBLPK

    • I9070UBLPK has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of I9070UBLPK by region

    First release
    February 26, 2014
    Last region
    April 2, 2014
    Duration
    36 days
    Regions
    2
    1. Day 1 · · 1 region
      ArgentinaPSN
    2. Day 36 · · 1 region
      ArgentinaARO

    Frequently Asked Questions

    I9070UBLPK is Android 2.3.6 (Gingerbread) firmware for Samsung Galaxy S Advance, released for Argentina (ARO, PSN). Samsung built it on 2014-01-09.

    No. A newer build for GT-I9070 is available: I9070ZSMG2. Install it instead of I9070UBLPK unless you need this exact version. The previous build was I9070UBLPI.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S Advance must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy S Advance running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 5 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S Advance

    No changelog details available.
    Model firmware by region