Samsung Galaxy S Advance I9070XXLQL
GT-I9070 1 country Android 4.1.2 (Jelly Bean)

Samsung Galaxy S Advance I9070XXLQL Firmware

Samsung Galaxy S Advance I9070XXLQL is an Android 4.1.2 (Jelly Bean) firmware for Italy (ITV, OMN). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9070XXLQI, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-I9070 is available: I9070ZSMG2.

Download firmware
8.8/10 (475)8,705 times
Android 4.1.2 (Jelly Bean)
OS Version
2013-12-05
First release
other regions until 2013-12-19
1
Countries
2
CSC codes
X (33)
Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S Advance use bootloader binary Z (35) (latest: I9070ZSMG2). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: I9070XXLQL
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    GT-I9070
    ITV Italy
    		I9070ITVLQ5 2013-12-19 2013-12-19 — —
    GT-I9070
    OMN Italy
    		I9070OMNLQB 2013-12-05 2014-05-09 — —

    No matching downloads

    How to flash I9070XXLQL

    • I9070XXLQL has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of I9070XXLQL by region

    First release
    December 19, 2013
    Last region
    May 9, 2014
    Duration
    142 days
    Regions
    2
    1. Day 1 · · 1 region
      ItalyITV
    2. Day 142 · · 1 region
      ItalyOMN

    Frequently Asked Questions

    I9070XXLQL is Android 4.1.2 (Jelly Bean) firmware for Samsung Galaxy S Advance, released for Italy (ITV, OMN). Samsung built it on 2013-12-05.

    No. A newer build for GT-I9070 is available: I9070ZSMG2. Install it instead of I9070XXLQL unless you need this exact version. The previous build was I9070XXLQI.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S Advance must be on bootloader binary X (33) or lower.

    This build uses bootloader binary X (33). It can be flashed on a Samsung Galaxy S Advance running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 6 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S Advance

    No changelog details available.
    Model firmware by region