Samsung Galaxy J3(2017) J330FXXU2AQL3
SM-J330F 1 country Android 7.0 (Nougat)

Samsung Galaxy J3(2017) J330FXXU2AQL3 Firmware

Build Date:

Samsung Galaxy J3(2017) J330FXXU2AQL3 is an Android 7.0 (Nougat) firmware for Russia (SER). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J330FXXU1AQI2: bootloader binary raised from 1 to 2, so after installing it there is no way back to older builds. A newer build for SM-J330F is available: J330FXXU4CZC2.

Download firmware
9.3 (493)4,518 times
Android 7.0 (Nougat)
OS Version
2017-12-15
Build Date
1
Countries
1
CSC codes
2
Bootloader binary

Bootloader binary 2. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J3(2017) use bootloader binary 4 (latest: J330FXXU4CZC2). If your device already runs binary 4, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: J330FXXU2AQL3
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-J330F
    SER Russia
    		J330FOXY2AQL3 2017-12-28 2.303 GiB
    SM-J330F_1_20210424153707_7zu1h3ndem_fac.zip
    		Download

    No matching downloads

    How to flash J330FXXU2AQL3

    • J330FXXU2AQL3 has bootloader binary 2. Your device must run binary 2 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal12.7 cm (5")
    • Display resolution1280 x 720 pixels
    • Display typeTFT
    • Processor frequency1.4 GHz
    • RAM2 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • SIM cardsDual SIM
    • Battery capacity2400 mAh
    • Weight142 g

    Frequently Asked Questions

    J330FXXU2AQL3 is Android 7.0 (Nougat) firmware for Samsung Galaxy J3(2017), released for Russia (SER). Samsung built it on 2017-12-15.

    No. A newer build for SM-J330F is available: J330FXXU4CZC2. Install it instead of J330FXXU2AQL3 unless you need this exact version. The previous build was J330FXXU1AQI2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.303 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J3(2017) must be on bootloader binary 2 or lower.

    This build uses bootloader binary 2. It can be flashed on a Samsung Galaxy J3(2017) running binary 2 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". No other build of this model uses binary 2.

    Other builds and changelog for Samsung Galaxy J3(2017)

    No changelog details available.
    Model firmware by region

    New firmware for other devices

    All latest builds