Samsung Galaxy Ace S5830DXKT5 Firmware
Samsung Galaxy Ace S5830DXKT5 is an Android 2.3.6 (Gingerbread) firmware for Indonesia (XSE), Philippines (GLB, SMA, XTC), XSO. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build S5830DDKQ8, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-S5830 is available: S5830ZSKPD.
8.9/10 (471)21,735 times
Android 2.3.6 (Gingerbread)
OS Version
2011-12-14
Build Date
n/a
Security patch
3
Countries
5
CSC codes
D (13)
Bootloader binary
Bootloader binary D (13). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.
Newer builds of Samsung Galaxy Ace use bootloader binary Z (35) (latest: S5830ZSKPD). If your device already runs binary Z (35), this build cannot be flashed.
All regional downloads
Pick your region (CSC) to download the matching firmware package.
Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
MODEM/CP Version: S5830DXKT4
No matching downloads
Device specifications
- Launched withAndroid 2.2
- Display diagonal8.89 cm (3.5")
- Display resolution320 x 480 pixels
- Processor frequency0.8 GHz
- Rear camera resolution5 MP
- Rear camera typeSingle camera
- SIM cardsSingle SIM
- Battery capacity1350 mAh
- Weight113 g
How to flash S5830DXKT5
- Install Samsung USB Drivers:Download Official Drivers
- Download Odin Flash Tool:
- S5830DXKT5 has bootloader binary D (13). Your device must run binary D (13) or lower: it is the 5th character from the end of your current build number.
- CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
- HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
- The Download Mode key combo depends on the model: see all combos.
Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.
Frequently Asked Questions
S5830DXKT5 is Android 2.3.6 (Gingerbread) firmware for Samsung Galaxy Ace, released for Indonesia (XSE), Philippines (GLB, SMA, XTC), XSO. Samsung built it on 2011-12-14.
No. A newer build for GT-S5830 is available: S5830ZSKPD. Install it instead of S5830DXKT5 unless you need this exact version. The previous build was S5830DDKQ8.
Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 131.451 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Ace must be on bootloader binary D (13) or lower.
This build uses bootloader binary D (13). It can be flashed on a Samsung Galaxy Ace running binary D (13) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 3 other builds of this model use the same binary, so you can switch between them in both directions.