Samsung GT-S7500 S7500BUMD1
GT-S7500 7 countries Android 2.3.6 (Gingerbread)

Samsung GT-S7500 S7500BUMD1 Firmware

Samsung GT-S7500 S7500BUMD1 is an Android 2.3.6 (Gingerbread) firmware for 7 countries, 7 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build S7500BUMB1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-S7500 is available: S7500ZULH1.

8.9/10 (453)30,759 times
Android 2.3.6 (Gingerbread)
OS Version
n/a
Build Date
n/a
Security patch
7
Countries
7
CSC codes
B (11)
Bootloader binary

Bootloader binary B (11). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung GT-S7500 use bootloader binary Z (35) (latest: S7500ZULH1). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: S7500BUMD1
    ModelRegionCSC VersionSizeFile nameDownload
    GT-S7500
    CNX Romania
    		S7500CNXMD1 — —
    GT-S7500
    SWC Switzerland
    		S7500SWCMD1 — —
    GT-S7500
    TCL Portugal
    		S7500TCLMD1 — —
    GT-S7500
    VD2 Germany
    		S7500VD2MD1 — —
    GT-S7500
    VGR Greece
    		S7500VGRMD1 — —
    GT-S7500
    VOD United Kingdom
    		S7500VODMD1 — —
    GT-S7500
    VOP
    		S7500VOPMD1 — —

    No matching downloads

    How to flash S7500BUMD1

    • S7500BUMD1 has bootloader binary B (11). Your device must run binary B (11) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    S7500BUMD1 is Android 2.3.6 (Gingerbread) firmware for Samsung GT-S7500, released for 7 countries, 7 CSC codes.

    No. A newer build for GT-S7500 is available: S7500ZULH1. Install it instead of S7500BUMD1 unless you need this exact version. The previous build was S7500BUMB1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung GT-S7500 must be on bootloader binary B (11) or lower.

    This build uses bootloader binary B (11). It can be flashed on a Samsung GT-S7500 running binary B (11) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 3 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung GT-S7500

    No changelog details available.
    Model firmware by region