Samsung Galaxy Tab3 7.0 T211UBUBNJ1 Firmware
Samsung Galaxy Tab3 7.0 T211UBUBNJ1 is an Android 4.4.2 (KitKat) firmware for Panama (TPA). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T211ZSANJ3: Android updated from Jelly(Android Bean) to Android 4.4.2 (KitKat); bootloader binary raised from S (28) to U (30), so after installing it there is no way back to older builds. A newer build for SM-T211 is available: T211XXBPA2.
9.2/10 (452)4,331 times
Android 4.4.2 (KitKat)
OS Version
2014-10-03
Build Date
n/a
Security patch
1
Countries
1
CSC codes
U (30)
Bootloader binary
Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.
Newer builds of Samsung Galaxy Tab3 7.0 use bootloader binary X (33) (latest: T211XXBPA2). If your device already runs binary X (33), this build cannot be flashed.
All regional downloads
Pick your region (CSC) to download the matching firmware package.
Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
MODEM/CP Version: T211UBUBNJ1
Device specifications
- Launched withAndroid
- Display diagonal17.8 cm (7")
- Display resolution1024 x 600 pixels
- Processor frequency1.2 GHz
- Rear camera resolution3 MP
- Rear camera typeSingle camera
- Front camera resolution1.3 MP
- Wi-Fi standardWi-Fi 4 (802.11n)
- Weight304 g
How to flash T211UBUBNJ1
- Install Samsung USB Drivers:Download Official Drivers
- Download Odin Flash Tool:
- T211UBUBNJ1 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
- CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
- HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
- The Download Mode key combo depends on the model: see all combos.
Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.
Frequently Asked Questions
T211UBUBNJ1 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Tab3 7.0, released for Panama (TPA). Samsung built it on 2014-10-03.
No. A newer build for SM-T211 is available: T211XXBPA2. Install it instead of T211UBUBNJ1 unless you need this exact version. The previous build was T211ZSANJ3.
Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 843.884 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Tab3 7.0 must be on bootloader binary U (30) or lower.
This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy Tab3 7.0 running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 4 other builds of this model use the same binary, so you can switch between them in both directions.