Samsung Galaxy Tab3 7.0 T211ZSANJ3
SM-T211 2 countries Android 4.1.2 (Jelly Bean)

Samsung Galaxy Tab3 7.0 T211ZSANJ3 Firmware

Samsung Galaxy Tab3 7.0 T211ZSANJ3 is an Android 4.1.2 (Jelly Bean) firmware for Hong Kong SAR China (TGY), Taiwan (BRI). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T211ZSANB1: Android updated from Jelly(Android Bean) to Android 4.1.2 (Jelly Bean). A newer build for SM-T211 is available: T211XXBPA2.

8.9/10 (454)8,668 times
Android 4.1.2 (Jelly Bean)
OS Version
2014-12-13
Build Date
n/a
Security patch
2
Countries
2
CSC codes
S (28)
Bootloader binary

Bootloader binary S (28). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Tab3 7.0 use bootloader binary X (33) (latest: T211XXBPA2). If your device already runs binary X (33), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: T211ZSANJ3
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-T211
    BRI Taiwan
    TGY Hong Kong SAR China
    		T211OZSANJ3 2014-12-13 766.396 MiB
    SM-T211_1_20151130191327_nyv214izvv_fac.zip

    No matching downloads

    How to flash T211ZSANJ3

    • T211ZSANJ3 has bootloader binary S (28). Your device must run binary S (28) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of T211ZSANJ3 by region

    Samsung released this build in all regions (2) on the same day, December 13, 2014.

    Device specifications

    • Launched withAndroid
    • Display diagonal17.8 cm (7")
    • Display resolution1024 x 600 pixels
    • Processor frequency1.2 GHz
    • Rear camera resolution3 MP
    • Rear camera typeSingle camera
    • Front camera resolution1.3 MP
    • Wi-Fi standardWi-Fi 4 (802.11n)
    • Weight304 g

    Frequently Asked Questions

    T211ZSANJ3 is Android 4.1.2 (Jelly Bean) firmware for Samsung Galaxy Tab3 7.0, released for Hong Kong SAR China (TGY), Taiwan (BRI). Samsung built it on 2014-12-13.

    No. A newer build for SM-T211 is available: T211XXBPA2. Install it instead of T211ZSANJ3 unless you need this exact version. The previous build was T211ZSANB1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 766.396 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Tab3 7.0 must be on bootloader binary S (28) or lower.

    This build uses bootloader binary S (28). It can be flashed on a Samsung Galaxy Tab3 7.0 running binary S (28) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Tab3 7.0

    No changelog details available.
    Model firmware by region