Samsung Galaxy S Advance I9070NELK3
GT-I9070 2 countries Android 2.3.6 (Gingerbread)

Samsung Galaxy S Advance I9070NELK3 Firmware

Samsung Galaxy S Advance I9070NELK3 is an Android 2.3.6 (Gingerbread) firmware for Austria (DRE), Italy (HUI). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9070JPLK2: bootloader binary raised from J (19) to N (23), so after installing it there is no way back to older builds. A newer build for GT-I9070 is available: I9070ZSMG2.

Download firmware
9.4/10 (488)6,600 times
Android 2.3.6 (Gingerbread)
OS Version
2012-11-27
First release
other regions until 2013-06-14
2
Countries
2
CSC codes
N (23)
Bootloader binary

Bootloader binary N (23). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S Advance use bootloader binary Z (35) (latest: I9070ZSMG2). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: I9070NELK3
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    GT-I9070
    DRE Austria
    		I9070DRELF2 2013-06-14 2012-12-10 457.404 MiB
    GT-I9070_DRE_1_20130614163700_9gx5zl9uq4.zip
    		Download
    GT-I9070
    HUI Italy
    		I9070HUILH2 2012-11-27 2012-12-10 530.043 MiB
    GT-I9070_HUI_1_20121127074919_gghrann89y.zip
    		Download

    No matching downloads

    How to flash I9070NELK3

    • I9070NELK3 has bootloader binary N (23). Your device must run binary N (23) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of I9070NELK3 by region

    Samsung released this build in all regions (2) on the same day, December 10, 2012.

    Frequently Asked Questions

    I9070NELK3 is Android 2.3.6 (Gingerbread) firmware for Samsung Galaxy S Advance, released for Austria (DRE), Italy (HUI). Samsung built it on 2012-11-27.

    No. A newer build for GT-I9070 is available: I9070ZSMG2. Install it instead of I9070NELK3 unless you need this exact version. The previous build was I9070JPLK2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S Advance must be on bootloader binary N (23) or lower.

    This build uses bootloader binary N (23). It can be flashed on a Samsung Galaxy S Advance running binary N (23) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". No other build of this model uses binary N (23).

    Other builds and changelog for Samsung Galaxy S Advance

    No changelog details available.
    Model firmware by region